Pcoip management console standard download -

Looking for:

PCoIP Management Console | Virtual Desktop System - Leadtek

Teradici PCoIP Management Console User Manual. TER Issue 14 - PDF Free Download.

The current release of the MC is only compatible with the following browsers: Firefox 23 or later Internet Explorer 8 and 9 Internet Explorer 11 in compatibility view The MC supports linking PCoIP host and zero client devices in fixed seating mode where the same zero client always connects to the same host.

If dynamically assigning zero clients to hosts is required, include a connection broker in the deployment. The tool may be able to support more than devices, but the current version was tested with a maximum of devices. Support for more than devices will be included in a future release of the tool. If your deployment has more than devices, contact your PCoIP equipment supplier for help on managing more than devices. The figure shows three groups of devices. Two of the groups share the same profile.

Figure Management Console Groups and Profiles Note some important rules regarding groups and profiles: Each group has only one profile associated with it. The same profile can be associated with multiple groups.

All configuration settings in a profile are written to all devices in a group when the profile is applied to the group. A profile can contain values for every configuration parameter, but this is not required.

You can define a profile that contains a subset of the configuration parameters. If the firmware on a device is updated when a profile is applied, the profile settings are written to the device after the new firmware is activated.

Profiles contain settings that let users specify if a device s firmware is updated based on the version of the firmware running on the device. Some settings are activated after a device is reset. Consider resetting your devices in the deployment after updating device configuration settings. When devices are added to a group and the group profile has not changed, apply the profile to the newly added devices and not the entire group.

This minimizes the number of device resets Fixed Seating The MC lets you link individual host and zero client devices so that each zero client always establishes a connection to the same host. This relationship is called fixed seating. To dynamically assign hosts to zero clients when your users log in, you must install a connection broker. If DNS- SRV discovery is not enabled, the MC must seek out and find devices using methods that are often subject to limitations, such as being unable to search more than its local subnet.

If you install a service record, the devices point to only one instance of the MC. If DHCP is not enabled, the MC must locate devices using methods that are often subject to limitations, such as being unable to search more than its local subnet. You have PCoIP devices with a firmware version earlier than in the network.

This device discovery method imposes a restriction that limits its usefulness. If a deployment cannot support any of the previous device discovery options, you can use the MC to configure devices. The MC supports a manual discovery feature that lets the MC find devices. Should this occur, you must perform another manual discovery search to find devices that were assigned new IP addresses.

See "Manual Device Discovery" on page 24 for more details. Enter DNS service configuration on domain controller. Right-click, and then select Other New Records 4. Fill in the entries as shown in Figure Enter the hostname where the MC is installed under the heading Host offering this service.

You can choose to set it to to reflect the listening port of the CMI server. Click OK to save and close the dialog. Expand the tree for the DHCP server, and expand the tree for the Scope to which you want to add options. Right-click Scope Options, and then choose Configure Options Click OK to save. Then enter the data entry in the Scope Options dialog.

It is recommended to configure both options together. If this setting is not blank during startup, the device tries to contact the MC by combining the string stored in this setting with variations of the domain name hierarchy. The algorithm uses the setting and the domain name hierarchy to search for a MC. With each FQDN variation, the hostname prefix remains constant while the domain hierarchy level changes.

The device sequentially attempts each FQDN possibility until a hit is found, at which point the device completes the DNS-based discovery. The algorithm may take several minutes to find the correct FQDN address of the MC this depends on the number of levels in the domain name hierarchy and the MC load.

In detail, the algorithm works as follows: 1. The device uses domain name variations based on the DHCP options 15 string. If the transmission times out, the device creates the next FQDN variation by proceeding one level up the domain hierarchy. The last domain name attempted has a single dot in the string. DHCP options 12 returns hostmachine1. Note that the DHCP server may return no value for either option.

Attempts 1 to 3 use the domain name from DHCP options 15 string. Failing transmissions for attempt 4 to 7, the device cycles back to using DHCP options Manual Device Discovery Manual device discovery is not an automated discovery mechanism. This mechanism supports discovering devices that are powered on and connected to the network when the MC is commanded to discover devices. In this situation, TER Issue 14 When the IP address of a device is known and the device has not been discovered, enter the address in the from IP field, and then select Discover Devices.

When a device is on a specific subnet but its IP address is not known, you can command the MC to discover the devices in a range of IP addresses using both the from IP and optional to IP fields. After you specify the address range, select Discover Devices. Note: This process can take a few minutes to complete depending on the number of addresses searched.

A status bar appears while the tool discovers devices. You can create AutoConfig rules to let one group have one or more criteria defined. The MC supports the following criteria to decide how zero clients are automatically assigned to groups using AutoConfig: Each group can have an optional AutoConfig rule associated with it. Rules are sets of optional password settings and optional IP address ranges: No Password: Add discovered zero clients to this group if they have no password configured.

Password: Add discovered zero clients to this group if they have the identical password configured for the criteria. IP address range: Add discovered zero clients to this group if the IP address falls within the range configured by the criteria. Above product spec is for reference only, actual spec rely on the real product and Leadtek keeps the right to alter.

Each sales region will impacts the product difference, please contact your supplier for making sure the actual product information. Manage Settings Continue with Recommended Cookies.

This release is a feature release with functional changes and bug fixes over release 5. Teradici Cloud Access Platform 2. Teradici Cloud Access Software 2. It is compatible with Tera2 Zero Clients on Firmware 5. These release notes provide a summary of key feature additions and compatibility notes for this firmware release.

This release is a security update with bug fixes to version 4. This release includes Wacom tablet support for Tera2 Zero Clients using firmware 4. This release includes an updated set of drivers for only the Virtual Machine to allow support for the latest version of VMware Horizon View Up to 6. Firmware updates for devices are available for download on help.

What happened to Management Console Standard? Will you continue to support my Tera1 device? Tera1 devices were end of life as of December 31, Formal support is no longer available and Management Console Release 1. How is the Management Console different from a Connection Broker? A connection broker dynamically assigns users to host computers based on login credentials. Report To report a potential security vulnerability with any HP supported product, send email to: hp-security-alert hp.

Legal information System management and security procedures must be reviewed frequently to maintain system integrity. Select a location. Europe, Middle East, Africa. Asia Pacific and Oceania. Select a language. Confirm Back.

Search all support. Search help. Tips for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number. Loading Results. The Virtual Agent is currently unavailable. Please try again shortly. Need help troubleshooting? Just ask.